what file do i buy to sharpen my saw chain
How to Sharpen a Chainsaw Concatenation Video
TOOL TIP
When to sharpen your chainsaw chain
Inspect the chainsaw concatenation to run across if its broken, needs repair or replaced. Your chain should be sharpened every fourth dimension you lot make full your chainsaw with fuel. If the wood debris from your concatenation looks like dust (as opposed to fries), this is an indicator that your chain is deadening and needs to exist sharpened. Having to strength your chain to get it to cut is some other sign of dull chain.
- Superlative Plate
- Cutting Corner
- Slide Plate
- Depth Estimate
- Gullet
- Toe
- Heel
- Rivet Hole
- Clearance Bending
- Depth Gauge
Footstep past Footstep: What You Should Exercise Before Sharpening a Chainsaw Chain
What Yous Volition Demand
-
Gloves
-
Protective eyewear
- Chainsaw Filing Kit (Round File, File Guide, Flat File and Depth Estimate Measuring Tool)
Step 1
If you have whatever questions about sharpening your Oregon chain, phone call our technical services department at 800-223-5168 , Mon through Friday between 7:30 a.m. iv p.m. PDT.
Step 2
Before you lot sharpen your chainsaw, you need to know the type of concatenation and sharpening angle specifications. Yous tin find this information in your chain saw possessor's manual or on the chain pack. The concatenation identification lawmaking is usually written on the driving link.
If you don't know your chain's type or number, ask your Oregon chain dealer or call our technical services department 800-223-5168 . Refer to specifications for sharpening chain with an Electric Grinder or past hand with a Round File.
Footstep 3
Put on your protective gear, including gloves and eye habiliment.
Stride 4
If you are sharpening concatenation while information technology is fastened to the chain saw bar, make sure it'south tensioned properly kickoff.
Footstep 5
Make sure your chain saw is turned off before you lot perform any maintenance.
Step 6
Wipe oil and grease off the chain. This step volition prevent build-up from occurring on the file'due south teeth or the wheel when grinding.
Pace seven
Inspect the chainsaw chain for damage.
Here's what you lot should look out for:
- Proper installation of necktie straps and bulldoze links
- Cracked or broken cutters, cutter top plates or tie straps
- Aptitude, cracked or burned drive links
- Severe abrasive harm
- Abnormally worn chain
- Wear patterns that may indicate a worn bar or sprocket. Refer to the Oregon Saw Chain Safety & Maintenance Manual for more information.
- Loose rivets (Try rotating the rivets with your fingers – if you tin can practise this, they are too loose.)
Footstep 8
If you are filing your chainsaw concatenation by hand, select and use the correctfile guide and file for your saw chain. This is the easiest manner to file saw chain.
Step 9
If the concatenation is broken, repair or replace it.
Step 10
Cheque and adjust depth gauges.
Pace eleven
Sharpen your concatenation to manufacturer'southward recommendations, keeping it balanced.
Stride by Step: How to Sharpen with a Circular File
The goal of filing is to remove all damage, while keeping the chainsaw chain balanced.
What Y'all Volition Need
-
Gloves
-
Protective eyewear
-
Chainsaw filing kit
-
Chainsaw chain
Footstep 1
Engage the chain restriction, then lightly clamp the chainsaw bar in demote vice. And then release the chain brake to exist able to rotate the chain past hand (be sure to clothing gloves when you practice this).
Step 2
If yous are using a file guide, place information technology over the cutter with the file in the gullet (between the cutter and the depth gauge). Brand sure the file guide has two points of contact, one betoken of contact on the cutter acme plate and two on the depth gauge.
Footstep 3
Hold the file in the right location so that 1/5", or 20%, of the file's diameter is positioned above the cutter's top plate. Using an Oregon File Guide is the easiest mode to hold the file in this position.
Footstep iv
Check to see if the pinnacle plate filing angle should be parallel to chainsaw concatenation centerline.
Footstep 5
Locate the cutter with the almost damage. Sharpen using steady, fifty-fifty strokes (the "full file length") to remove the damage while counting the number of file strokes.
You'll know the damage is removed when the cutter has a shiny, silver face. File all of the cutters with the aforementioned number of strokes per cutter from the within to the exterior and so that the cutter lengths are equal.
Footstep 6
Complete all the cutters on one side of the chain, before turning your concatenation to switch sides.
File from the within of each cutter to the outside. Complete all the cutters on 1 side of the chain. Once you are washed, turn your saw around to repeat the process for the other side of the chain. Remember, go along all cutter lengths equal.
Step 7
File dorsum to remove damage and continue top plates equal in length.
Footstep viii
Recheck depth gauges.
Step past Footstep: How to Sharpen a Chainsaw Chain with an Oregon Electric Sharpener
These instructions are meant to exist general guidelines. Refer to your grinder transmission for set-up use and instructions.
Grind your concatenation so that it meets the recommendations of the manufacturer. Use a quick tapping motion to minimize over heating of the ground surface.
Step ane
Check the grinder wheel shape.
Step two
Fix vise assembly to the correct top plate filing angle.
Refer to your grinder's manual to learn the best way to do this.
Step 3
Use the recommended top-plate cutting angle to set the proper grinder caput angle.
Step 4
Check that the vise blocking handle is screwed in tight and that the chain is blocked.
Footstep v
Turn on the electric sharpener.
Stride 6
Sharpen the cutter by lowering the arm-motor unit.
Stride 7
When you are done sharpening the cutter, heighten the arm and loosen the handle.
Step 8
Run the chain forward to position the next cutter to be sharpened.
Footstep ix
Block once again with the handle and sharpen.
Step ten
When all the cutters are sharpened, turn the machine off and unplug the power cable.
Step 11
Apparel vitrified grinding wheels often to maintain correct shape.
Use either a rotary dresser or a dressing brick.
Step past Step: What You Should Practise Later on Sharpening a Chainsaw Chain
Pace 1
Check and suit depth gauges using instructions constitute here.
Step 2
Make clean off any debris, so lubricate the chain thoroughly with bar and chain oil. For the best results, soak the chain overnight.
Pace 3
Store the sharpened saw chain in a container with lubricant so that it'southward gear up for its adjacent use.
Oregon strongly encourages condom piece of work practices and always recommends the employ of advisable safety dress. Persons demonstrating technical product information in videos or photography do not necessarily represent proper rubber habits for whatsoever given job.
Source: https://www.oregonproducts.com/en_ca/how-to-sharpen-a-chainsaw-chain
0 Response to "what file do i buy to sharpen my saw chain"
Post a Comment